常见问题及处理方法 Common problems and solutions

1、连接输入电源后，显示屏，不亮或者没显示，一般都是保险管烧了或者电源线问题
①电源线未插紧无法正常供电：检查电源线插入状态，插紧后可正常工作：
②电源线故障：更换电源线（如电饭锅、电脑线等）可正常工作;

③保险管烧坏：需要更换保险管, 检查仪器后面的电压是否拔到220V或230V(国内标准电压) ，如果电压拔到110V或者115V，则需要拔回220V或230V才可以更换保险管(仪器出厂电源插头处配有一个备用保险管，拉开更换后即可正常工作) 。更换方式及位置如下图:

(用螺丝刀撬开，把外面备用的换到里面位置即可)

2、全部配件都戴好，按开始ON/OFF键的时候,出现了长鸣的嘀嘀嘀的报警声音，然后仪器自动停止了工作，离子头不冒泡：

出现了长鸣的嘀嘀嘀的报警声音是因为水中含盐份过高，浓度超过了仪器设定的数值2.5左右, 需要重新换一盆清水, 离子头重新冲洗一下, 放适量的盐。

3、每次用完后离子头要怎么样处理：

每次排毒完后离子头可以用清水直接冲洗干净，然后通风晾干，晾干后用袋子包裏起来（离子头不能长期直接暴露在空气中，容易被氧化，使用寿命缩短) 。

4、关于调节模式(MODE)：
模式表示离子头电解工作的强弱，MODE 1是离子头电解比较弱，MODE 5是离子头电解最强。

5、时间调节说明：
仪器开机默认工作时间是30分钟，必须先调好时间再按开始键 ( ON/OFF) , 每按一下时间按键，时间增加5分钟，注意如果仪器开始工作了，则不能调节时间的。最高可调到60分钟。

1, connect the input power, the display, not lit or not displayed, are generally fuse burned or the power cord problem
① power cord is not plugged can not be normal power supply: check the power cord into the state, plug can be normal work;
② power cord failure: replace the power cord (such as rice cookers, computer lines, etc.) can work properly;
③ fuse burned: need to replace the fuse, check the voltage behind the instrument is pulled to 22oV or 23oV (domestic standard voltage), if the voltage pulled 11ov or 115v, you need to pull back 22oV or 23oV before you can replace the fuse The factory power plug is equipped with a spare fuse, opened to replace the normal work). Replacement and location as shown below:

(With a screwdriver pry open, the outside can be replaced to the inside position)

2, all the accessories are worn, press the start oN / oFF key, there was a long clear sunny sunny alarm sound, and then the instrument automatically stopped working, ion head does not bubble:

Appear the sound of the Ming Ming murmur alarm sound is because the salt water is too high, the concentration exceeds the value set by the instrument 2,5 or so, you need to change a pot of water, re-wash the ion head, put the right amount of salt .

3, after each run high how to handle:

After each detoxification ion head can be rinsed directly with water, then ventilated to dry, dry bag with bag up (ion head can not be long-term direct exposure to the air, easily oxidized, shortened service life).

4, on the adjustment mode (MODE):
Mode indicates the strength of high sub-head electrolysis, MODE 1 is relatively weak ion head electrolysis, MODE5 is the strongest ion head electrolysis.

5, time adjustment Description:
The default working time of the instrument is 30 minutes. The time must be adjusted before pressing the start button (0N / OFF). Each time you press the time button, the time will increase by 5 minutes. Note that the time can not be adjusted if the instrument starts working. Adjustable up to 60 minutes.